06/19/13 - SERVICE MANUAL *.* FIRMWARE
Login




This is featured post 1 title

Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation test link ullamco laboris nisi ut aliquip ex ea commodo consequat.

This is featured post 2 title

Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation test link ullamco laboris nisi ut aliquip ex ea commodo consequat.

This is featured post 3 title

Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation test link ullamco laboris nisi ut aliquip ex ea commodo consequat.

This is featured post 4 title

Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation test link ullamco laboris nisi ut aliquip ex ea commodo consequat.

This is featured post 5 title

Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation test link ullamco laboris nisi ut aliquip ex ea commodo consequat.

RESET OKIDATA TONER DRUM - for OKI 5100 , C5200, C5500, C5650, 5250N, 3200, 3200N, Xante Ilumina Codes, network card reinitialization and more..

General instructions for reset

 

1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"

3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.
Attention !!
If your printer has an internet adapater card, you can lose your network settings, mac, and menu for network configurations, when you clear NV_RAM TABLE 1 CLEAR.
             If you cleared NV_RAM Table you need to initialize your network card.
1. Turn the printer off.
2. Disconnect printer from the network.
3. Hold in the "Test" button on the network card.
4. Turn the printer on, keeping the "Test" button pressed.
5. Continue holding down the "Test" button until the display shows "Network Initalizing" and "Wait A Moment" shows on the display . . . then release the "Test" button.
6. When "ONLINE" status shows on the display your network card should be re-registered in the NV RAM.
------------------------------------------------------------------------------------------------------------------------

How to turn off toner page counting on the OKI C5400n

1) Turn off printer.
2) Turn on printer, while holding the + and - buttons.
3) The LCD Shows 'OKI User', Scroll to "Engine Diag Mode", hit enter. The display shows "Diag Mode 01.02.02 S-Mode"
4) Scroll to Eng Param Set 2, Hit Enter.
5) Scroll to Toner Sensor(it may be the first one), hit enter, Change setting to "Disable"
6) To set the "Disable" setting you need to press the ONLINE, CANCEL and - Buttons at the same time, pressing ONLINE first.
7) Press the Back Button.
8) Turn off the Printer, Leave for 10 seconds, and Turn back on, as normal.
------------------------------------------------------------------------------------------------------------------------

C7200 maintenance Menu's and reset tonner for C7200, C7300, C7500

1) Turn on Printer while holding the 1 & 2 buttons.

2) Using button #1 scroll down untill you see "Diagnostic Mode xx.xx.xx", then hold down buttons 2 & 3.

3) You now have "Engine Diag Mode Level 4" showing on the display.

4) Use Buttons 1 & 5 to scroll between menu's. Scroll down to "Counter Set".

5) Use Buttons 2 & 6 to scroll between menu items. Use buttons 3 & 7 to change the value you wish to alter.

6) The Flashing number is the value you have highlighted. Use Buttons 2 & 6 to change that value.

7) When you have made any changes you need to, hold down buttons 1, 3, and 5. The screen will flash 3 times, then an * will appear at the end of the screen. The Value has been set.

8) The "ID" unit appears to be the drums, setting these values changes the drum usage according to the printer.
The Toner counts are in percentages, and can be changed from 000% to 999%, where 0% is no use, and 100% is totally used.
The "Dot Count"s set how many times each colour has been used, in the life of that toner(?).
The "Total Dot Count" is the same as the above, but for the entire life of the printer.
The "Replace" values for belt, fuser, drums, and toners show how many times each of those units have been replaced.
The Printer life limit seems like an odd one... its there to make you replace the printer after x(600000) number of prints?
There are also life limits for toners, drums, fuser units, belts etc, which can be changed from the default values.
The (cmyk) "ID Unit" shows how many pages have been printed that include that colour since that item has been installed.
The (cnyk) toner percentages can be changed here manually, but is no use if you've turned off toner counting in the below step.

9) To turn off Toner counting:

After getting into Eng Diag level 4, scroll down to "Engine Parameter Set 2".

Use the 2 & 6 buttons to scroll between options. Scroll to "Toner Sensor".

By Default, this is "Enable".

Change the values by using the 3 & 7 buttons. When you've changed the value to "Disable" press both the 3 & 7 buttons together, and the * will appear, showing that you've set the value correctly.

You can also apply the above change to the "ID Unit"s aswell, being the image drums, to stop any counting of the drum units, allowing them to be used untill image quality suffers.

The above change can also be made to the "Belt Unit" and i'm guessing Fuser unit aswell.
------------------------------------------------------------------------------------------------------------------------
 Turn off toner page counting on the OKC3200N
We don\t  want to do the NVRAM complete reset because we can lose network settings.
Diagnostic mode
1) Turn off printer.
2) Turn on printer, while holding the + and - buttons.

3) The LCD Shows "OKI User", Scroll to "Engine Diag Mode", press "enter".

The display shows "Diag Mode xx.xx.xx S-Mode" .
At this point you should wait for the initialization cycle to complete. I mean for all the motors and gears to have finished their noises and cycles – otherwise you will end up with a LCD switching between two different info screens - not a big deal but still annoying.
1) Pressing the "Online", "Cancel", "Enter", "-" and "Back" AT THE SAME TIME (not in any sequence – at the same time). Yes! That is 5 buttons.

2) After within two seconds the LCD menu will show "READY". If it doesn’t, release button and repress buttons again.

3) The buttons release sequence is important. So, read this before letting go your five fingers: Release the "Enter" button first and THEN the four others. LCD is still showing "READY".

4) Press the "Online" and "Cancel" button at the same time BRIEFLY. Don’t wait before pressing them after the five fingers sequence otherwise you will miss your time slot.
You can always switch back from the "READY" to the "Diag Mode xx.xx.xx S-Mode" menu by pressing the five buttons again.
Now you see "Eng Diag Level 2".
Or
Press either the + or – button until "CONSUMABLE COUNTER SET" is displayed, press the Enter button; you are now in the menu to set various consumables.

1) Press either the + or – buttons to scroll through the various consumables, at the desired consumable (ie. "K-ID UNIT …" for the Black Image Drum Unit, "C-Toner" for cyan toner, etc.), press the Enter button and the last digit of the count will start flashing.

2) Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count. Note that it will not show the remaining but the usage (100% means it is empty).

3) Once the count is at the level you desire, press and hold the On-line, Cancel simultaneously until the numbers stop flashing; you have reset that consumable’s count to the number you specified. Note that you may end up with a different value then the one that was entered when saving. The printer engine is probably jumping to the nearest registered/acceptable value. If someone find a way to save the exact value, let us know.

4) Press the + or – buttons to move to the next consumable and repeat at step 5.

5) Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus (reverse of steps 2 through 4) until "INITIALIZING" is displayed. Or turn printer off and on.

6) You're finished! Now log in to the web interface with your browser and check to see the remaining life of your consumables.

 You can also get to level 3 and level 4 after the release of the five fingers step by pressing something else then the "online" and "cancel".
------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C9300n
1) Power ON printer while holding both the 0, 1, 6, 7 buttons until “OKIUSER” message apear in LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...

------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C5450n

1) Power ON printer while holding both the + & - buttons until “OKIUSER” message apear in LCD.
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...
------------------------------------------------------------------------------------------------------------------------

Xante Ilumina Codes - Same as 9800

1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...

Xante Ilumina Codes

1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...

------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C5200
1) Power ON printer while holding "+(up)" & "-(down)" and "help" buttons until “OKIUSER” message apear in LCD
2) Press + or – button until “ENGINE DIAG MODE” is displayed;
3) Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
4) Press + or – button until “NV-RAM INITIAL” is displayed
5) Press "ENTER" again;
6) Will appear "TABLE 1" message;
7) Press "ENTER" until "EXECUTING RESET" message appear. the "NV-RAM INITIAL" message will BLINK...
This procedure reset TONER, DRUM, FUSER and BELT...
8) power OFF printer, wait 10 sec, and power ON again...
Possible also work for the C9500 printers as well.
------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C7500 printer (and other C7000 series).
1. Hold buttons 0 + 1 + 6 + 7 on startup.

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items (button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made hold buttons 1 + 3 + 5. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.

NOTES:
An "ID" unit is an imaging drum. The life used (shown as pages) doesn't need to be changed. Instead you change the "life limit" to get more use out of the drum. The default figure is 20,000 pages. If you are careful with your drums and keep light away from them they should easily last to 40,000 pages and beyond

Each colour toner counter shows life as percentage used. So a toner showing 30% has used up 30% of its toner. 100% would indicate a near empty toner. This is the reverse of the toner life shown from the "usage menu" when the printer is in normal operation, which shows the toners as a percentage life remaining.

The toner life limit default is set at 100%. Another option to use, instead of changing each toner's percentage life used (i.e. cranking back from 97% down to 87%), would be to increase the toner life limit above 100%. For example, increasing it up to 110%. In practice the OKI printers seem to fairly accurately record the amount of toner used, so an extra 10% might be all you get out of a toner. What feedback can other people offer on how much extra life they get?

If you are swapping over toners or drums from another secondhand printer into your printer, it will not know they are "new" and your printer will still show the existing life values for the old units. If you know the life used in these "new" units you can go into the printer's counter set menu and reset the values so they are more accurate.


------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C5500 

1) Turn off printer.
2) Hold down "+" and "-" buttons at the same time, and keep them held down while turning printer back on... continue to hold until the word "OKIUSER" appears.
3) Use "-" button to scroll down to "FUSE KEEP MODE".
4) Press "Enter" button, hold for approx. 10 seconds, then release.
5) Press "Enter" button again, followed by rapid release and repress with hold for approx. 10 seconds.
6) Release "Enter" button, then press and let up one more time quickly.
7) You will see "INITIALING" and then "ONLINE" messages.

If you currently have an error message for toner cartridge life, the message will continue to be shown until after you've sent one print job, and then it will usually disappear for awhile. It will stay gone for longer if you have your printer set up so the toner sensor is turned off.

------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C7400 


1) PRESS AND HOLD BUTTONS 1 + 5 AND TURN ON THE PRINTER (WHILE CONTINUING TO HOLD THE BUTTONS).
(For Oki C7200 Printers you press and hold buttons 0 + 1 + 6 + 7).

(addition information) "MAINTENANCE MENU" will appear on the screen within a few seconds. Then about 5 seconds later, "OKIUSER" will appear.

THE REST OF THE STEPS ARE THE SAME FOR BOTH C7400 AND C7200 SERIES PRINTERS...

2. Press button 0 several times until "DIAGNOSTIC MODE xx.xx.xx" shows.

3. Hold buttons 2 + 3 until "ENGINE DIAG LEVEL 4" shows.

4. Press button 1 to scroll to "COUNTER SET".

5. Press button 2 to scroll through menu items (button 6 scrolls backwards)

6. To alter the value of an item, first press button 3 to select the digit to be altered. The selected digit will slowly flash. (Button 3 moves to the right through the digits. Button 7 takes you to the left.)

7. Then press button 2 to increase the value of the selected digit. Press button 6 to decrease the value.

8. When the changes have been made hold buttons 1 + 3 + 5. The screen will flash three times and then an * will appear on the right of the screen. The new value is set.

9. To leave the counter set menus, turn the printer off.

------------------------------------------------------------------------------------------------------------------------

Drum, Toner, Fuser, Belt Reset on OKI C5300

1. Just like all other instructions, get into the special menu by holding down the menu+ and menu- keys while turning the unit on.
2. When you see the message "OKIUSER" CAREFULLY release both buttons at the same time.
3. Use the menu- or the menu+ to get to "ENGINE DIAG MODE".
4. Press enter. DIAGNOSTIC MODE XX.XX.XX will appear.
5. Now press both the online and the back buttons, and "ENG DIAG LEVEL 4" will be displayed.
6. Press enter.
7. Press menu+ twice to "ENGINE PARAMETER SET 2"
8. Press enter.
9. Press menu+ twice to get to "TONER SENSOR ENABLE" (with a * in the lower right hand of the display window.
10. Press enter and the word "ENABLE" will begin to blink, indicating it can be changed.
11. Press menu+ and the word will change to "DISABLE", still blinking. This is a toggle, make sure to not hit the button twice.
12. This is the important step: simultaneously press the online, cancel, and back buttons, and let them all go simultaneously. this sets your selection.
13. There are other things that can be done here in the same fashion, but that is out of the scope of this document.
14. Use the "BACK" and the "MENU-" keys to back out all the way to the message "INITIALIZING", then power off, wait 10 seconds, and power back on.
If you skip an step don't just turn off the printer, use the back button and the menu minus(-) key to escape back to the message "initializing", then turn off the printer!
------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C5540 
1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C5950n 

1.With the printer turned off,remove the chips from the cartridges
1a.The cartridges should be in the printer but withOUT chips
2.Turn-on it while you press the (+)&(-) buttons,enter the maint.menu
3.You have to:
3a.Set FACTORY MODE
3b.Disable the toner,id check sensors (you must DOIT everytime is write it because the printer in every mine passage will re-enable it!!!
3c.Execute the FUSE-KEEP mode by tapping TWICE the enter button in the fuse-keep mode menu (EXECUTE)

The printer will turn on and after the adjustment cycles he performs you should see all the toners at 0% but the printer will be ON-LINE!

NOW:
4.With the printer ON install the chips and close the lid
Values should be at 100% (but in a kind of safe mode)
5.Turn the printer off
6.Open the lid,DON'T CLOSE IT!
7.Enter the maintanance menu (WITH THE LID OPEN)
8.Set shipping mode again
9.Disable again the toner and ID sensors
10.Turn off the printer
----the lid always open----
11.LID ALWAYS OPEN , turn on the printer and enter the maintenance menu
12.Double check the shipping mode and the TONER-ID SENSOR DISABLE
13.If ok until here turn off the printer
13.Close the lid and turn him on normally

Toner levels should be at 100%


------------------------------------------------------------------------------------------------------------------------
Drum, Toner, Fuser, Belt Reset on OKI C810 

1) Turn off printer.
2) Hold down "+" and "-" and "enter" and "cancel" buttons at the same time, and keep them held down while turning printer back on... continue to hold until the word "SYSTEM MAINTE" appears.
Than press ENTER, and enter password "000000". you will see OKIUSER
3) Use "-" button to scroll down to "FUSE KEEP MODE".
4) Press "Enter" button, hold for approx. 10 seconds, then release.
5) Press "Enter" button again, followed by rapid release and repress with hold for approx. 10 seconds.
6) Release "Enter" button, then press and let up one more time quickly.
7) You will see "INITIALING" and then "ONLINE" messages.

If you currently have an error message for toner cartridge life, the message will continue to be shown until after you've sent one print job, and then it will usually disappear for awhile. It will stay gone for longer if you have your printer set up so the toner sensor is turned off.

If you currently have a error message for drum life, it will continue to appear, but you will still be able to print.

------------------------------------------------------------------------------------------------------------------------
Service Menu on the Oki C610 (and likely other printers).

Menu + and Menu - and Help

That will get the service menu. The password is 000000

 

[×]

Có những file đã bị đặt pass, nếu muốn có pass các bạn có thể để lại 1 Comment ngay tại bài đó kèm theo mail của các bạn, nếu được duyệt sẽ có pass tại thư của bạn . Blog-HoaiTrang .!